Free Complete Guide to Log Homes E-book with every order!Free Complete Guide to Log Homes E-book with every order!

westernloghomesupply

Phone (970) 315-2660

  • Monday - Friday
  • 8 AM - 5 PM

PC-Petrifier Rotted Wood Hardener - 16 fl oz

Water-based wood hardener
PC-Petrifier Rotted Wood Hardener - 16 fl oz
Orig. Price: $13.99
54983164440
Usually ships the next business day
chat Chat with a Log Product Expert

Product Description

Download PC Petrifier MSDS

Description::
PC-Petrifier® is a single component adhesive, formulated to fully penetrate and revitalize rotted wood.  Modern technology has allowed us to develop a water base wood consolidant that is environmentally friendly.  PC-Petrifier's® low viscosity allows deep penetration into soft rotted wood fiber, restoring old wood to near structural integrity.  Seal and restore rotted soft wood fibers in window sills, sashes, frames, trim, decorative beams and columns, etc.


PC-Petrifier® can also be used to prepare old wood for priming and painting. Apply to exposed wood grain to protect from damage.  Not for structural repairs. If you have structural wood damage, please see our PC-Rot Terminator®.   Do not use in conjunction with PC-Wood Guardian™ or other Borate products.

Directions:
Area to be treated must be dry, free of dirt, dust and grease.  Remove loose paint varnish or flaky wood. Generously apply PC-Petrifier® by pouring, spraying, brushing or sponging onto area to be restored.  Repeatedly saturate the rotted wood fibers to enable the deepest possible penetration.  Let cure until solid and not tacky to the touch.

Application Tips:
Since the depth of penetration may depend on the porosity of the wood, to get deeper penetration drill or poke small holes to allow access down to solid wood. On painted surfaces drill small holes (1/8 inch or larger) to allow access to soft wood. When restoring a vertical surface; drill holes in a downward angle and then saturate with PC-Petrifier®.  If needed, apply more PC-Petrifier® to affected area. Normally one treatment will be sufficient.  After area is restored, fill holes and missing wood with PC-Woody® epoxy.  Best results are obtained when applying at temperatures above 45°F to dry wood.  Successful application depends on the wood’s dryness, porosity and preparation.

Uses:
PC-Petrifier® is great for sealing and restoring rotted soft wood fibers found in window sills, sashes, frames, trim, fences, decks, paneling, log homes, playground equipment, picnic tables, cellar doors and planking (exposed end grain).  PC-Petrifier® can be used to prepare old wood for priming and painting. For structural wood repair use PC-Rot Terminator® epoxy consolidant.

Deep penetrating, pre-mixed water based, environmentally friendly product
for interior or exterior use.





More Info

PC-Petrifier® is a single component adhesive, formulated to fully penetrate and revitalize rotted wood.  Modern technology has allowed us to develop a water base wood consolidant that is environmentally friendly.  PC-Petrifier's® low viscosity allows deep penetration into soft rotted wood fiber, restoring old wood to near structural integrity.  Seal and restore rotted soft wood fibers in window sills, sashes, frames, trim, decorative beams and columns, etc.


PC-Petrifier® can also be used to prepare old wood for priming and painting. Apply to exposed wood grain to protect from damage.  Not for structural repairs. If you have structural wood damage, please see our PC-Rot Terminator®.   Do not use in conjunction with PC-Wood Guardian™ or other Borate products.

Directions:
Area to be treated must be dry, free of dirt, dust and grease.  Remove loose paint varnish or flaky wood. Generously apply PC-Petrifier® by pouring, spraying, brushing or sponging onto area to be restored.  Repeatedly saturate the rotted wood fibers to enable the deepest possible penetration.  Let cure until solid and not tacky to the touch.

Application Tips:
Since the depth of penetration may depend on the porosity of the wood, to get deeper penetration drill or poke small holes to allow access down to solid wood. On painted surfaces drill small holes (1/8 inch or larger) to allow access to soft wood. When restoring a vertical surface; drill holes in a downward angle and then saturate with PC-Petrifier®.  If needed, apply more PC-Petrifier® to affected area. Normally one treatment will be sufficient.  After area is restored, fill holes and missing wood with PC-Woody® epoxy.  Best results are obtained when applying at temperatures above 45°F to dry wood.  Successful application depends on the wood’s dryness, porosity and preparation.

Uses:
PC-Petrifier® is great for sealing and restoring rotted soft wood fibers found in window sills, sashes, frames, trim, fences, decks, paneling, log homes, playground equipment, picnic tables, cellar doors and planking (exposed end grain).  PC-Petrifier® can be used to prepare old wood for priming and painting. For structural wood repair use PC-Rot Terminator® epoxy consolidant.

Deep penetrating, pre-mixed water based, environmentally friendly product
for interior or exterior use.

Reviews

You May Also Need...

Recently Viewed Items...