Outlast Q8 Log Oil - Best Price + Free Shipping and Fast Delivery!
Outlast® Q8 Log Oil is one coat oil based product that is a EPA registered wood preservative designed to protect against mold, mildew,rot and insects (termites, powder post beetles) on log homes and on wood siding. It provides maximum water repellency and sheer trans-oxide color with one coat coverage. Outlast Q8 Log Oil is a totally non-film forming EXTERIOR treatment that will never crack or peel. The solution penetrates into the wood to provide protection, not just on the surface, but also deep into the wood cell structure.
What really sets Outlast® Q8 Log Oil apart is that it is more than just a stain, it is also a preservative!
Coverage: 150 - 300 Square Ft per gallon
Proper wood prep is a critical first step to successful penetration of the Outlast Q8 Log Oil. Outlast Kleenstart Cleaner is the recommened cleaner prior to applying Outlast Q8 Log Oil. Kleenstart will clean mold and mildew and remove mill glaze. One quart makes 5-8 gallons and cleans up to 1200 square feet of surface area.
KleenStart is an oxygenated granular cleaner that mixes in hot or cold water. Mix it up, spray with a pump-up garden sprayer, leave it on for about 10 minutes, and rinse with a pressure washer. Kleenstart often does most of the scrubbing for you!
Add this to your Q8 Log Oil order today by selecting it under the Cleaners drop down menu.Outlast Q8 Log Oil Estimated Delivery Times Outlast Q8 Log Oil Video Presentation
Preparing the Surface
Great Preparation is the Key to Application Success!
Q8 Log Oil penetrates and protects. The surface must be porous free of mill glaze, dirt, and previous coatings. Outlast Kleenstart is recommended prior to the initial application of Q8 Log Oil and subsequent applications. The better the preparation of the wood the longer the Q8 Log Oil treatment will last.
Wood preservatives are toxic to wood damaging organisms like termites, powder post beetles, and fungus.
Q8 Log Oil is an EPA approved wood preservative so applications of a borate treatment is not necessary prior to applying Q8 Log Oil.
Wood preservatives do not protect against non wood eating insects. Ants, cockroaches, beetles, mites, spiders, fleas, ticks, silverfish, dirt daubers, bees and wasps will not crawl on, nest on or burrow through coatings treated with NBS 30 Additive.
Mold, Mildew, and Algae
Q8 Log Oil alone stops decay, mold, and fungi. Use Outlast Mold-Buster when additional protection is required to control surface mold, mildew, and algae growth on the coating. It is recommended for use with coatings applied in high humidity environments and for applications where mildew has been a problem in the past.
Applying Q8 Log Oil
Outlast Q8 Log Oil can be applied during a wide range of weather conditions. Q8 Log Oil will not penetrate as well on wet or cold logs/wood. Below 50 degrees, Q8 Log Oil will become too thick to pump through a pump sprayer and may require hand brushing. Streaking of pigment may result if it rains within 36 hours of treatment. Simply re-spray the surface with more product, let it sit for 15 minutes and smooth out any streaks with a stiff paintbrush. Apply as much Q8 Log Oil as the wood will absorb. Clean tools with dish detergent and warm water or mineral spirits.
Caulking and Chinking
As wood dries it is natural for cracking and checking to occur. It is recommended to fill any gaps larger that 1/4" with caulk. Cracks/checks less than 1/4" should be flooded with Q8 Log Oil.
If applying a sealant after Q8 Log Oil wait for it to cure which is 2+ weeks prior to caulking/chinking. Curing time can vary with weather conditions. Q8 Log Oil can cure in 2 weeks with many warm and dry days. Low temperatures, humidity, and wet weather can lengthen the cure time.
When time does not allow for proper curing time, the caulking/chinking should be done prior to applying Q8 Log Oil.
Samples and Testing
We always recommended performing a 1 coat color test. Samples are available for color testing. Wait 24 hours after applying a Q8 Log Oil sample before observing the color. The color will lighten as the product dries.