SculpWood Putty Kit
Download SculpWood Putty (White) MSDS
Download SculpWood Putty (Brown) MSDS
SculpWood Putty is a flexible, clay like epoxy putty for the repair of wood that has been gouged, part or harmed by abuse and rot. Use it to fill nail and screw gaps, and supplant missing wood areas on moldings, window housings, turnings, fascia boards, and so on. SculpWood Putty is astoundingly simple to utilize, and when cured can be cut, sanded and machined just like wood. It holds clasp well and will accept most paint and primers. SculpWood Putty is 100% waterproof and is perfect for both exterior and interior surface applications. Dissimilar to other comparable items SculpWood Putty contains no solvents, water or VOCs. It cures completely by chemical response and won't contract or get to be fragile over the long haul. This solvent free formula gives SculpWood putty boundless time span of usability. SculpWood Putty has been determined by draftsmen and utilized by expert to permanently restore woodwork on my important buildings, homes, and other wooden structures. Each kit comes with two equal size containers (one of resin (part A white) and the other of hardener (part B brown).
Features:
100% waterproof
VOC and solvent free
Superior bond strength
Very low odor
Exterior and interior applications
Will not shrink or become brittle after curing
Hardener and resin are easily mixed by hand
Convenient 1:1 mixing ratio
Can be easily tooled and shaped
Will not slump or sag
Can be painted and primed to match and existing finish
Once cured can be carved, machined or sanded
Will hold nails, screws, fasteners etc.
Application: With disposable gloves on each hand, knead together one part of SculpWood Part A with one Part B by volume. Mix no more than can be applied within 15 minutes. Start with a golf ball size of Part A and a golf ball size of B. They are different colors, so knead them together for at least 1 full minute - or until the mix is one completely uniform color. Insufficient blends give poor results.
Technique: When cured, SculpWood can be sawed, nailed, carved, machined, and sanded. SculpWood can also be stained or painted. (If stained, you will need to experiment with various colors as it does not accept stain color the same as the adjacent wood.)
TIP: When it is warmer than 80 degrees outside, flatten out the mixed ball of Part A and B into a pancake. If left in a ball, heat will build up and it will begin to cure in the middle.
TIP: Use a putty knife dipped in acetone or white vinegar to smooth the rough shape. Always leave slightly more material in the void than you need to fill it. In about 24 hours, it is simple to sand flush to the original surface. If you sand too much, or under fill the void, the surface will have to be wetted with RotFix before additional SculpWood can be added. You can also mix RotFix and SculpWood to achieve a more desired consistency.
Clean-up: Uncured Mixed SculpWood (Part A and Part B) may be cleaned up with white vinegar or acetone, and then flushed with water.
SculpWood Putty Kit
Download SculpWood Putty (White) MSDS
Download SculpWood Putty (Brown) MSDS
SculpWood Putty is a flexible, clay like epoxy putty for the repair of wood that has been gouged, part or harmed by abuse and rot. Use it to fill nail and screw gaps, and supplant missing wood areas on moldings, window housings, turnings, fascia boards, and so on. SculpWood Putty is astoundingly simple to utilize, and when cured can be cut, sanded and machined just like wood. It holds clasp well and will accept most paint and primers. SculpWood Putty is 100% waterproof and is perfect for both exterior and interior surface applications. Dissimilar to other comparable items SculpWood Putty contains no solvents, water or VOCs. It cures completely by chemical response and won't contract or get to be fragile over the long haul. This solvent free formula gives SculpWood putty boundless time span of usability. SculpWood Putty has been determined by draftsmen and utilized by expert to permanently restore woodwork on my important buildings, homes, and other wooden structures. Each kit comes with two equal size containers (one of resin (part A white) and the other of hardener (part B brown).
Features:
100% waterproof
VOC and solvent free
Superior bond strength
Very low odor
Exterior and interior applications
Will not shrink or become brittle after curing
Hardener and resin are easily mixed by hand
Convenient 1:1 mixing ratio
Can be easily tooled and shaped
Will not slump or sag
Can be painted and primed to match and existing finish
Once cured can be carved, machined or sanded
Will hold nails, screws, fasteners etc.
Application: With disposable gloves on each hand, knead together one part of SculpWood Part A with one Part B by volume. Mix no more than can be applied within 15 minutes. Start with a golf ball size of Part A and a golf ball size of B. They are different colors, so knead them together for at least 1 full minute - or until the mix is one completely uniform color. Insufficient blends give poor results.
Technique: When cured, SculpWood can be sawed, nailed, carved, machined, and sanded. SculpWood can also be stained or painted. (If stained, you will need to experiment with various colors as it does not accept stain color the same as the adjacent wood.)
TIP: When it is warmer than 80 degrees outside, flatten out the mixed ball of Part A and B into a pancake. If left in a ball, heat will build up and it will begin to cure in the middle.
TIP: Use a putty knife dipped in acetone or white vinegar to smooth the rough shape. Always leave slightly more material in the void than you need to fill it. In about 24 hours, it is simple to sand flush to the original surface. If you sand too much, or under fill the void, the surface will have to be wetted with RotFix before additional SculpWood can be added. You can also mix RotFix and SculpWood to achieve a more desired consistency.
Clean-up: Uncured Mixed SculpWood (Part A and Part B) may be cleaned up with white vinegar or acetone, and then flushed with water.